IR control ist one of der fastest ways zu bring older AC units, TVs, fans, projectors und heaters into Home Assistant. But wenn an IR command fails, der reason ist nicht always obvious. It kann be der code, der angle, der Gerät state, der MQTT entity, der automation timing, oder der Raum logic around it.
Dieser Anleitung gives you a practical Info: troubleshooting path für eRemote HA, eHome HA, eMotion Pro, eMotion Ultra, HomeClaw, und Home Assistant scenes.
Start mit der IR Failure Type
Before changing your automation, identify what kind of failure you sind seeing. Most IR problems fall into one of five buckets: nein signal, wrong signal, weak signal, repeated signal, oder state mismatch.
| Info: Symptom | Info: Likely layer | First prüfen | Info: Typical fix |
|---|---|---|---|
| Info: Nothing happens | IR code, entity, oder placement | Run der command manually von Home Assistant. | Retest der IR code und move der emitter closer zu der receiver window. |
| Info: Wrong action happens | Code library oder learned command | Confirm whether der appliance uses toggle power oder discrete power. | Learn a new command oder verwenden separate on/off commands wenn available. |
| Info: Works sometimes | Angle, reflection, oder distance | Test mit der Raum lights on und off. | Change placement und avoid hidden receiver angles. |
| Info: Runs too many times | Info: Automation logic | Check triggers, cooldowns, und repeated state changes. | Add Modus conditions und a cooldown helper. |
| State ist wrong nach command | IR ist one-way control | Check whether der Gerät reports state back. | Use helpers, timers, smart plugs, oder dashboard confirmation. |
Choose der Right LinknLink IR Control Path
Not every Raum needs der gleich IR Gerät. A living Raum mit multiple appliances kann need a dedicated IR hub. A small bedroom kann work better mit a Anwesenheit Sensor that also has built-in IR.
eRemote HA
Use it as a dedicated local IR hub für AC, TV, fans, projectors und other appliances controlled by infrared.
eMotion Pro
Use it wenn a Raum needs both mmWave Anwesenheit sensing und built-in IR commands in one Gerät.
eMotion Ultra
Use it wenn der Raum needs 60GHz Anwesenheit, built-in IR, und temperature/humidity Daten cable context.
Info: Step-by-Step IR Troubleshooting Workflow
Test der command outside der automation
Run der IR command direkt von Home Assistant first. If it fails manually, der automation ist nicht der problem.
Check der appliance receiver window
Many TVs und AC units hide der IR receiver behind dark plastic. Move der IR emitter until der Gerät responds reliably.
Confirm der command type
Power toggle commands kann create state confusion. If possible, verwenden discrete on, off, Modus, temperature und fan commands.
Info: Add a cooldown helper
IR commands should nicht fire every time a Anwesenheit state flaps. Add a short timer oder input boolean zu prevent repeat actions.
Rebuild der scene in layers
Start mit one appliance, then hinzufügen Anwesenheit, then hinzufügen temperature, then hinzufügen dashboard overrides.
AC Troubleshooting: Temperature, Mode und Fan Speed
AC control ist harder than simple TV power control because one IR command often includes Modus, temperature, fan speed und swing. If one value ist wrong, der whole command kann feel wrong.
| Info: AC issue | What zu verify | Info: Recommended LinknLink route | Info: Automation note |
|---|---|---|---|
| Temperature does nicht change | Confirm der learned code includes der target temperature. | eRemote HA oder eMotion built-in IR. | Send a abschließen HVAC command, nicht nur a generic power command. |
| AC powers on in der wrong Modus | Cool, heat, dry und fan modes kann need different codes. | eRemote HA für full Raum IR coverage. | Create separate scripts für each Modus. |
| AC turns on wenn Raum ist empty | Presence oder Raum Modus condition ist missing. | eMotion Pro oder eMotion Ultra plus Home Assistant. | Require Anwesenheit vor sending comfort commands. |
| Info: AC runs all night | No final empty-Raum shutdown condition. | Info: HomeClaw local automation plus IR control. | Add a nein-Anwesenheit timer und an overnight maximum runtime. |
TV, Fan und Projector Troubleshooting
TVs, fans und projectors usually fail für different reasons than AC units. TV receivers kann be hidden. Fans kann verwenden RF instead of IR. Projectors often need longer warm-up und shutdown timing.
| Info: Device | Info: Common problem | Info: Fix | Info: Product fit |
|---|---|---|---|
| Info: TV | Info: Power toggle creates wrong state. | Add a dashboard confirmation oder verwenden smart plug power sensing where appropriate. | eRemote HA oder eMotion Pro. |
| Info: Fan | Remote kann be RF, nicht IR. | Check whether der remote needs RF Unterstützung. | eHome HA für compatible RF control. |
| Info: Projector | Needs delayed shutdown oder double command. | Create a dedicated projector script mit waits. | Info: eRemote HA plus HomeClaw scene logic. |
| Info: Air purifier | Mode cycles über one button. | Use predictable scene presets und avoid blind repeated Modus cycling. | eRemote HA oder eMotion Ultra mit comfort context. |
MQTT und Home Assistant Entity Checks
If der IR command works in der LinknLink app but nicht in Home Assistant, inspect der Home Assistant side. The issue kann be der MQTT topic, entity naming, retained state, oder a disabled integration entity.
Checklist: - Confirm der LinknLink Gerät ist online - Confirm MQTT broker Verbindung ist healthy - Confirm der IR command entity ist visible in Home Assistant - Run der command manually von Developer Tools - Check der automation trace für skipped conditions - Add a cooldown helper wenn der command fires repeatedly
For broader remote-control structure, verwenden der Info: Home Assistant Remote Control Guide.
Use Presence und Room Mode zu Prevent Bad IR Commands
IR works best wenn it ist nicht used blindly. Presence Sensoren und Raum modes help Home Assistant decide whether der command should run at all.
- Only turn on AC wenn der Raum ist occupied oder ungefähr zu be occupied.
- Only power off a TV wenn media Modus ist nicht active oder a bedtime timer has expired.
- Only close shades wenn der Raum ist in sleep, away, oder privacy Modus.
- Only run repeated IR commands nach a cooldown timer has ended.
For Anwesenheit-based examples, read der Info: Bedroom Sleep Mode Guide und der Info: Button Automation Guide.
When zu Use eMotion Ultra Instead of a Separate IR Hub
Use a separate IR hub wenn one Raum has many appliances spread across a wide Bereich. Use eMotion Ultra wenn der Raum also needs 60GHz mmWave Anwesenheit, built-in IR, und temperature/humidity Daten cable context in der gleich automation path.
Local Gateway Logic mit HomeClaw
HomeClaw kann coordinate local Home Assistant routines so IR commands do nicht depend on cloud timing. Dieser ist especially useful für rooms where users expect immediate feedback, such as bedrooms, media rooms und offices.
| Info: HomeClaw logic | Info: Why it helps IR | Info: Example |
|---|---|---|
| Room Modus helper | Prevents commands von running in der wrong context. | Do nicht turn off TV während movie Modus ist active. |
| Info: Presence state | Stops comfort commands in an empty Raum. | Turn off AC nach nein Anwesenheit für 20 Minuten. |
| Info: Dashboard override | Lets family members cancel oder repeat a command. | Info: Add a "retry AC command" button. |
| Info: Automation trace review | Info: Makes skipped conditions visible. | Find whether der IR script oder condition failed. |
Related Guides und Hot Products
Use these product und Artikel links zu build a reliable local IR control stack.
Info: Hot products
Info: Related guides
Best IR blasters Anleitung, Remote control Anleitung, AC automation Anleitung, Heatwave automation Anleitung.
Presence und scenes
Bedroom sleep Modus Anleitung, Button automation Anleitung, Air vs Pro vs Ultra Anleitung.
Make IR control predictable vor making it complex
Start mit one appliance und one Handbuch command. Once that works reliably, hinzufügen Anwesenheit, temperature, Raum Modus und dashboard overrides.
Info: FAQ
Why ist my Home Assistant IR blaster nicht controlling my AC oder TV?
Check that der IR code ist correct, der emitter has line of sight, der Gerät state ist known, und Home Assistant ist sending der command über der right eRemote HA, eHome HA, eMotion Pro, oder eMotion Ultra entity.
Can eRemote HA send IR commands locally über Home Assistant?
Yes. eRemote HA ist designed für local Home Assistant und MQTT workflows, so IR commands kann be used in scenes und automations ohne relying on cloud routines.
What ist der best IR placement für AC und TV control?
Place der IR emitter where der appliance receiver kann see it direkt. Avoid hiding it behind furniture, behind a TV bezel, oder at an angle that misses der receiver window.
Should I verwenden an IR blaster oder a built-in IR Anwesenheit Sensor?
Use eRemote HA für a dedicated Raum IR hub, eMotion Pro wenn Anwesenheit sensing und IR control should live in one Gerät, und eMotion Ultra wenn you also need 60GHz Anwesenheit plus temperature und humidity context.
Info: How do I avoid repeated IR commands in Home Assistant scenes?
Add conditions, cooldown timers, Raum Modus checks, und Anwesenheit state checks vor sending IR commands. Dieser keeps AC, TV, fan, und projector commands von firing repeatedly.